roar's profile
| Gender | Male |
|---|---|
| Age | U10 |
| Experience | ２〜３ years |
-
Use racket, rubber
-
- Racket
- Balanced racket for a cut of the balance of momentum and control. Recommended to cut introductory...
-
- Rubber (Front)
-
- Rubber (Back)
- Grain shape close to a grain high.Change system table rubber to exhibit also high knuckle effect ...
-
User review
-
-
-
2023/05/14
This rubber is soft and easy to control, so it is a rubber for beginners. Both the sheet and the sponge are soft, so even players with less power will be able to bite into it and get a good turn. However, for some reason I can't beat the rotation, so I can counter at all. However, the maximum value of power is low, so I think it is difficult for advanced users to use it.
However, due to the soaring price of rubber, this rubber has also been raised from 4000 yen to 4800 yen.
Since it's for beginners, it's quite painful to raise the price to nearly 5,000 yen..Rigan Spin, which was in the same price range, was only raised to 4,200 yen, so it's a bit disappointing in that respect. However, even though the price has been raised because it has a long lifespan, I think there is enough cost performance.Overall Speed Spin Control Hardness Soft
Recomend racket Swat
-
-
-
-
2023/06/11
This rubber is hard anyway. It was the hardest tension rubber I have ever touched. I usually use Kyo Leopard, so I found it very easy to use.
It is a normal momentum with a light hit, but it bounces tremendously at the time of a strong hit such as a drive. The loop also has the strength of catching the seat, and it takes a lot of rotation. Speed balls are hard and have a strong impact, so I think they are for advanced players.
It bounces, but it's easy to do because you don't feel that momentum with techniques such as benches.
I also tried cutting, but I thought that the rubber was not suitable for cutting. Because it is hard and hard to bite into the rubber, there were many mistakes when trying to cut the cut. It was fine at all for the knuckle cut.
I thought it was a rubber that could fight regardless of the front and back!Overall Speed Spin Control Hardness Hard
Recomend racket Innerforce Layer ALC
-
-
-
2023/05/29
Compared to Carl P1, this rubber is less prone to irregular changes, but it is very easy to use because the grains easily fall down. I tried hitting with a thin sponge, but the cut block stops, and the push tends to rotate upwards, making it a little arc and stable.
I also tried cutting. I'm usually a front cut man, so I can't cut much when I use grain height, but even I was able to cut quite a bit.
It is highly recommended for those who use grain height for the first time!Overall Speed Spin Control Hardness Little soft
Recomend racket Swat Carbon
-
-
-
2023/05/08
It's a cut man, but I used it for a while in the past!
This rubber flies quite a lot in the leopard, and the speed comes out considerably. It uses a softer and bouncy sponge than Turbo Blue, so it's a little less addictive, but it's easier to use. Of course, the loop is easy to do, and it takes a tremendous amount of rotation. And above all, it is the speed drive that shows the true value of this rubber. It is easy to bite into the sponge, so it is easy to become an arc, and it also has speed, so it will be a great ball.
It's about cutting. I used this rubber as a cut man, but honestly the cutting performance was subtle..It is quite difficult to suppress because it is easily affected by the opponent's rotation and it is a flying rubber. However, when you can cut it in perfect condition, a tremendous cut will go.
It is not recommended for cutman, but it is a rubber that is highly recommended for driveman!Overall Speed Spin Control Hardness Little hard
Recomend racket Acoustic Carbon
-
-
-
-
2023/05/14
Although it is a tension type grain height, it was a rubber that was easy to control with a thin sense of tension in a good way. The speed and change of other tension grains are amazing, but I think it's a disadvantage because it's hard to control. However, the Morist LP is a little inferior in speed and change, but the control is easy to make as non-tension.
Although it is OX, I also cut it. When it came to cutting, I definitely felt the tension element, and I had the impression that it was a little bouncy. It became a straight cut, and it seemed difficult for the other party to drive.
Recommended for cutmen who want to make aggressive cuts, and players who want to be more aggressive than non-tension grains, but who want to play more stable grain heights!Overall Speed Spin Control Hardness Little soft
Recomend racket SANALION S
-
Racket
Producer
Grip
Review Ranking
Rubber
Producer
Type
-
Get the Amazon gift card at a Review!
20 points are added in the post. You can replace it by Amazon Gift Card worth $5.00 with 1000 points.
